logo
Главная страница Новости

Common Causes and Troubleshooting Methods for Insufficient Power in Construction Machinery

Я оцениваю помощь от Пола, он префессионал и знает точно какие части мне нужны. Мой КАТ шел назад работать без проблем.

—— Рафаэл

Получил конечную передачу и свое красивое я думаю. Мы имеем иметь его быть собранным в нашем экскаваторе Хитачи ЗС330, мои машины идем работать снова теперь. Большое спасибо

—— kevin

Быстрая пересылка, приезжанные части хорошее качество, наш двигатель отремонтирован и совершенно бежит при максимальном сила. Спасибо, бог благословляет.

—— Мухаммед

Оставьте нам сообщение
компания Новости
Common Causes and Troubleshooting Methods for Insufficient Power in Construction Machinery

Insufficient machine power is a common but high-level fault in construction machinery. As a mechanic, this fault can be challenging to diagnose accurately on-site. The simplest cause is often fuel circuit blockage or clogged filters.

However, accurate diagnosis under on-site conditions requires substantial practical knowledge and experience. Based on personal experience, the following summary may serve as a reference for industry peers.

In general, insufficient machine power arises from either:

  1. Engine power deficiency,

  2. Overload in the machine’s operational system,

  3. Or a combination of both.


I. Engine Power Deficiency

1. Engine cannot reach rated RPM under maximum load

  • Symptoms: Engine speed below rated RPM, sometimes accompanied by heavy black smoke or even stalling.

  • Steps to check:

    • Verify if the machine is overloaded.

    • Reduce load to standard specifications; if the issue is alleviated, overload is the cause.

    • Note: Arbitrary increase of hydraulic system pressure also constitutes overload.

    • If pressure is returned to standard but engine power is still insufficient, consider whether the hydraulic flow is too high. For variable hydraulic systems, flow and pressure are inversely proportional: high flow within pump specifications requires lower pressure; otherwise, the engine will overload.

    • Caution: Adjusting hydraulic pump flow without a flow meter or specifications may lead to incorrect settings and further issues.

2. Engine under full throttle, maximum load, low machine action speed

  • Symptoms: Engine load feels light, RPM may exceed rated speed, but machine action is slower than factory specifications.

  • Cause: Machine load is insufficient to utilize maximum engine performance.

3. Performance parameter reference

  • Testing must be based on machine factory performance parameters, as there is no direct engine power measurement device installed.

  • Examples of parameters to measure:

    • Mining trucks: maximum speed under full load

    • Wheel loaders: lift and unload time under specified conditions

    • Bulldozers: travel speed unloaded

    • Excavators: full cycle action times

  • Measurement requires stopwatch timing for accuracy.

4. Turbocharged engine power testing

  • Method: Measure instantaneous maximum intake boost pressure, record data to evaluate engine power output.


II. Overload in Machine Operational System

1. Symptoms of system overload

  • Engine produces black smoke, unstable RPM, tendency to stall.

  • Machine performance parameters exceed factory specifications (hydraulic system, torque converter, or operational abnormality).

2. Observations

  • During testing, machine action parameters may drop only slightly.

  • Accurate measurement requires stopwatch timing of cycles.


III. Combined Engine Performance Decline and System Overload

1. Symptoms

  • Engine stalls during testing, often without heavy black smoke.

2. Troubleshooting

  • Determine which hydraulic circuit causes stalling by elimination method.

  • Frequently, variable hydraulic system circuits are involved, often due to variable pump malfunction, preventing minimum flow adjustment.

  • Less common in fixed displacement pump systems, where the typical issue is flow reduction.

3. Measuring machine circuit performance

  • Machines of the same tonnage generally have similar performance parameters.

  • Measurement can be done if the machine travels straight; if drifting occurs, additional diagnostic steps are required.


Notes

  • These methods are based on practical experience with used machines or post-repair testing, not blindly copying new machine specifications.

  • Accurate diagnosis requires knowledge of engine, hydraulic system, and machine operational parameters, combined with systematic observation and testing.

Время Pub : 2024-12-05 17:26:35 >> список новостей
Контактная информация
Guangzhou Anto Machinery Parts Co.,Ltd.

Контактное лицо: Mr. Paul

Телефон: 0086-15920526889

Факс: +86-20-89855265

Оставьте вашу заявку (0 / 3000)